• 首页期刊介绍编委会期刊订阅广告合作联系我们English
  • 选择皮肤:
李姝蕾,金东海,桂幸民.尾缘S3面积比梯度对涡轮后机匣的影响[J].航空动力学报,2020,(2):422~431
尾缘S3面积比梯度对涡轮后机匣的影响
Influence of S3 area ratio gradient at trailing edge on turbine rare frame
投稿时间:2019-07-23  
DOI:10.13224/j.cnki.jasp.2020.02.021
中文关键词:  涡轮数值模拟  涡轮后机匣  二次流动控制  角区分离  尾缘S3面积比梯度
英文关键词:turbine numerical simulation  turbine rear frame  secondary flow control  corner separation  S3 area ratio gradient at trailing edge
基金项目:国家科技重大专项(2017-Ⅰ-0005-0006)
作者单位
李姝蕾 School of Energy and Power Engineering,Beijing University of Aeronautics and Astronautics,Beijing 100191,China 
金东海 School of Energy and Power Engineering,Beijing University of Aeronautics and Astronautics,Beijing 100191,China
Collaborative Innovation Center for Advanced Aero-Engine,Beijing 100191,China
 
桂幸民 School of Energy and Power Engineering,Beijing University of Aeronautics and Astronautics,Beijing 100191,China
Collaborative Innovation Center for Advanced Aero-Engine,Beijing 100191,China
 
摘要点击次数: 109
全文下载次数: 100
中文摘要:
      针对整流叶栅与支板融合设计中难以采用三维叶片造型对二次流进行控制的情况,开展对涡轮后机匣内部整流叶栅尾缘S3面积比梯度的研究。以某15级涡轮为例,通过数值模拟的方法,对比三种设计的内部流场和气动性能,验证了降低尾缘S3面积比梯度控制角区二次流的方法。结果显示:尾缘S3面积比梯度从001降低到-005时,整流叶栅总压恢复系数从0979升高到0991,5%展高处S参数从0011降低到0005,吸力面和轮毂端壁处的回流区消失,角区分离得到有效控制;尾缘S3面积比梯度从-005降低到-010时,吸力面角区流动速度增加,5%展高处S参数不再变化、堵塞程度降低、轴向密流比(AVDR)升高、总压恢复系数升高。
英文摘要:
      For the intergraded design of support plate and outlet guide vane, where it's difficult to apply the three-dimensional blade design, the secondary flow in the outlet guide vane can be controlled by changing S3 area ratio gradient at the trailing edge. The numerical results of inner flow field and aerodynamics performance of three designs were compared in a 15 stage turbine. The results showed that when the gradient reduced from 001 to -005, the overall total pressure recovery coefficient of the outlet guide vane increased from 0979 to 0991, and the S parameter on 5% span reduced from 0011 to 0005. The back-flow zone on the hub endwall and the suction side of the blade disappeared, and the corner separation was effectively controlled. When gradient reduced from -005 to -010, the flow velocity in the corner zone increased, and at the 5% span, corner blockage lessened, axial velocity density ratio (AVDR) increased, total pressure recovery coefficient increased, yet the S parameter didn't change.
查看全文  查看/发表评论  下载PDF阅读器
关闭
.